[QSG]BN68-03690A-01Eng-0520, INSTRUKCJE OBSŁUGI
[ Pobierz całość w formacie PDF ]
Quick Setup Guide
Congratulations on the purchase of your new Samsung TV.
Read this setup guide to get your TV up and running quickly.
Step 4
: Connect External Devices
Connecting an audio device (Home Theater, etc.)
Connect your TV to your Home Theater or other audio device to enjoy enhanced
Sound quality.
Connecting an AV device (DVD/ Blu-ray player, cable/satellite box, etc.)
1-800-SAMSUNG (726-7864)
Samsung Electronics America, Inc.
85 Challenger Road Ridgeield Park, NJ 07660-2112
Samsung Electronics Canada Inc.
55 Standish Court Mississauga, Ontario L5R 4B2
Call Center hours of operation: Mon-Sun, 9:00 AM -12
AM EST.
To register this product, visit: www.samsung.com/
register.
STOP
Please do not return this unit.
If you have problems operating your
TV, call:
1-800-SAMSUNG (726-7864)
For web support please visit:
www.samsung.com/support
Use one of the connections below to connect your TV to an external A/V device. We recommend using HDMI for the highest picture quality.
Digital Audio connection
Using an Optical Cable
Best Connection
HD connection (up to 720p/1080i)
HDMI to DVI Cable
(Not Supplied)
Optical Cable (Not Supplied)
Digital Audio System
Very Good Connection
Using an HDMI Cable
DVD / Blu-ray player / HD Cable Box / HD STB
(Set-Top-Box) satellite receiver
OPTICAL
HD connection (up to 720p/1080i)
HDMI Cable
(Not Supplied)
Step 1
: Install the Stand
Follow the steps below to connect the TV to the stand.
✎
NOTE
x
Make sure to distinguish between the front and back of the Stand and
Guide Stand when assembling them.
x
Make sure that at least two persons lift and move the PDP TV.
x
Stand the product up and fasten the screws. If you fasten the screws with
the PDP TV placed down, it may lean to one side.
1
With your TV upright, connect the
TV to the Stand as shown.
Using a HDMI to DVI Cable
Device
HDMI OUT
Device
DVI OUT
Connecting a PC
Lowest Quality Connection
Good Connection
Component connection (up to 720p/1080i)
Connect your TV to a PC to use it as a Monitor.
Audio/Video connection (480i only)
Using an Audio/Video Cable
Using a Component Cable
2
Fasten the four screws (M4 X L8) at
position.
DVD, Blu-ray player, cable box, STB
satellite receiver, VCR
HD connection
DVD / Blu-ray player / HD Cable Box / HD Satellite receiver (STB)
Video Cable (Not Supplied)
Device
Device
Using a HDMI to DVI Cable
AUDIO OUT
COMPONENT OUT
VIDEO OUT
AUDIO OUT
DVI OUT
Component Cable (Not Supplied)
HDMI to DVI Cable
(Not Supplied)
Front
Audio Cable (Not Supplied)
Rear
Audio Cable (Not Supplied)
✎
When connecting to
AV IN
on the back of your TV, attach the
video cable (yellow) to the green jack next to the
AV IN
label.
The jack will not match the color of the video cable (yellow).
Step 2
: Install the Batteries into the Remote
To install batteries into your remote control, follow these steps:
1.
Lift the cover on the back of the remote upward as shown in the igure to the
right.
Step 5
: Run Plug & Play
When you turn on your TV for the irst time, it automatically launches the Plug &
Play function. With Plug & Play, you can select the On Screen Display language,
set the clock mode, and launch the TV’s channel memorizing process.
It also displays connection instructions similar to those in this guide.
To navigate while Plug & Play is running, press the Up, Down, Left or Right arrow
buttons on your remote. To make a selection, press the
ENTER
E button.
To skip a screen, press the
MENU
button. To turn on your TV, press the
POWER
button on the remote or on the TV. To run Plug & Play, follow these steps:
1
Using your remote control,
select the language for the On
Screen Display (OSD), and then
press the
ENTER
E button.
✎
Most cable systems are Standard(STD) systems, If you are not sure about
what kind of cable system you have, contact your cable company.
✎
If your TV is attached to a cable or satellite box, skip Steps 3 through 5. After
Plug & Play is complete, set your TV to Channel 3 or 4, according to the
directions for your cable or satellite box.
2.
Install two AAA batteries.
✎
Make sure to match the +
and - ends of the batteries
to the diagram in the battery
compartment.
7
Select the time zone in which you live, and then press
ENTER
E.
8
After the time zone screen, The connection method for best HD screen
quality is displayed. Press Right arrow button on your remote to view each
screen in succession. Press the Blue button to skip this section.
9
The Enjoy your TV. screen appears. Then press the
ENTER
E button.
3.
Replace the cover.
4
The TV memorizes the available
channels. This process can take
up to 45 minutes.
Plug & Play
Step 3
: Connect Power and Antenna or Cable
Auto Program in Progress.
DTV Air : --
Plug & Play
If You Want to Rerun Plug & Play
1.
Plug & Play
Air : --
Select Language of the OSD.
Press the
SOURCE
button on your remote, then select TV mode.
DTV Cable : --
Cable : --
Cable : 35
VHF/UHF Antenna
English
Español
Français
48%
2.
Press the
MENU
button on your remote to display the menu.
Language
Connect Ant In to
3.
Press the ▲ or ▼ button to select Setup, and then press the
ENTER
E
button.
Antenna Cable (Not Supplied)
Stop
• Wall cable jack
• VHF/UHF Antenna
• Cable or Satellite box
Ant or Cable Out
E Enter m Skip
U Move E Enter
or
4.
Press
ENTER
E again to select Plug & Play.
5
After the TV has memorized the
channels, choose the Clock Mode.
Select Auto if you have a digital
channel in your area. Select Manual
if you don’t, or if you have a cable or
satellite box. When done, press the
ENTER
E button.
✎
If you select Manual,
the clock setting screen
appears.
6
Select the daylight savings
time setting: Off, On or Auto
and then press the
ENTER
E
button.
2
Select Home Use, and then
press the
ENTER
E button. If
you select Store Demo, the TV
will reset your picture and audio
settings every 30 minutes.
Plug & Play
Plug & Play
Best to use 75 ohm (round) cable.
Set the Clock Mode.
Select ‘Home Use’ when installing this TV in your home.
Auto
Manual
Make sure the AC power cord is plugged in securely to
the wall outlet and the TV.
Clock Mode
Store Demo
Home Use
L Move E Enter
U Move E Enter m Skip
3
Select the Antenna Source
to memorize. you must select
Antenna Source to same type
as your cable system type. After
selecting source, select Start;
then press the
ENTER
E
button on your remote.
Plug & Play
Select the Antenna source to memorize.
Plug & Play
Air
Cable
Auto
Start
Start
Start
Set to daylight saving time.
Auto
On
Auto
DST
U Move E Enter m Skip
U Move E Enter m Skip
BN68-03690A-01
Step 6
: Remote Control
Changing Channels and Adjusting the Volume
Adjust the volume by pressing the Volume button
on the remote.
Remote Control Buttons and Functions
Change the channels by pressing the Channel button on the remote.
✎
If your TV is attached to a cable or satellite box, change the channel using
the box’s remote.
✎
You can also change the channels by pressing the z button on the front panel of your TV and adjust the volume by pressing the y button.
✎
This is a special remote control for the visually impaired and has Braille points on the Power, Channel and Volume buttons.
Selecting a Source
Changing the Picture Mode
To watch a movie on your Blu-ray player or watch your
favorite TV show, you must select the correct source.
A source is a device, such as a Blu-ray/DVD player,
a cable/satellite box, antenna or a cable TV input.
Sources can be connected to your TV through the
HDMI, DVI, Component, Composite, or through the
Antenna or Cable In connections.
To view the signal from a source connected to the HDMI, DVI, Component, or
Composite jack, press the
SOURCE
button on your remote. E
a
ch time you press
the
SOURCE
button, you change to a different source.
Your TV has three preset Picture modes with factory adjusted settings, each
designed to give you an excellent picture under speciic conditions.
To change the Picture mode, press the
P.MODE
button on your remote. The irst
time you press it, your TV displays the current setting. Thereafter, each time you
press the
P.MODE
button, you change the mode of the picture on the screen.
The Picture modes are listed and described in the table below:
Displays and selects the available video sources.
Turns the TV on and off.
Press to directly access channels.
Description
Mode
Dynamic
Brightens picture. For a vibrant, enhanced image in brightly lit or
sunny room.
Press to select additional digital channels (digital) being
broadcasted by the same station. For example, to select
channel “54-3”, press “54”, then press “–” and “3”.
Standard
For a bright, detailed picture in a normally lit room.
Viewing the On Screen Menus
Returns to the previous channel.
Movie
For a studio quality cinema picture in a dimly lit or dark room.
Cuts off the sound temporarily.
To view the On Screen Menus, follow these steps:
1.
MEDIA.P
FAV.CH
To change the Picture mode, follow these steps:
1.
With the power on, press the
MENU
button on
your remote. The main menu appears.
The menu’s left side has the following menu
options: Picture, Sound, Channel, Setup, Input, Application, and Support.
Changes channels.
With the TV on, press the
MENU
button on your remote, then select Picture.
Adjusts the volume.
2.
Select Mode, the Press the
ENTER
E button.
Displays the channel list on the screen.
3.
On the Mode menu in Picture, use the ▼ or ▲ on your remote to select the
picture mode you want.
Brings up the OSD.
2.
Press the ▲ or ▼ button on your remote to select a menu option, and then
press the
ENTER
E button.
4.
Press the
ENTER
E button to inish the change.
Displays Media Play (USB).
MEDIA.P
FAV.CH
FAV.CH
: Displays Favorite Channel Lists on the screen.
3.
When done using the menu, press the
EXIT
button on your remote to exit.
Quickly select frequently used functions.
Displays information on the TV screen.
Setting the Clock
Changing the Screen Size
Selects the on-screen menu items and changes the values
seen on the menu.
Before you can use your TV’s On/Off Timer, you must set the clock. To set the
clock, follow these steps:
1.
Your TV has several screen size options, each designed to wor
k
best with speciic
types of video input. If you have a cable box or satellite receiver, it may have its own
set of screen sizes as well.
To change the screen size, press the
P.SIZE
button on your remote. The irst time
you press it, your TV displays the current setting. Thereafter, each time you press
the
P.SIZE
button, you change the size of the picture on the screen.
The following sizes are available:
Returns to the previous menu.
Turn on your TV, press the
MENU
button on your remote, then select Setup →
Time.
Exits the menu.
2.
Select Clock Mode, and then press the
ENTER
E button.
A
B
C
D
Use these buttons in a speciic feature. For details, refer
to e-Manual.
3.
Choose Auto or Manual.
x
If you select Auto, set the current time automatically using the time from
digital broadcast.
x
If you select Manual, you can set the Month, Day, Year, Hour, Minute
and am/pm directly by pressing up, down, left and right arrow button on
your remote.
P.SIZE
MTS
: Press to choose stereo, mono, or Separate Audio
Program (SAP broadcast).
P.SIZE
: Lets you choose the picture size.
CC
: Controls the caption decoder.
16:9 Wide screen
4:3 Standard screen
Wide Fit
4.
Press the
RETURN
button on your remote when done.
Connecting a USB Device for Media Play
Zoom 1
Zoom 2
Screen Fit
You can enjoy photo and
music iles stored on a USB
device by connecting it to the
TV and using the Media Play
feature. To connect a USB
device for Media Play, follow
these steps:
1.
✎
Screen Fit: Displays the full image without any cut-off when HDMI (720p /
1080i / 1080p) or Component (1080i / 1080p) signals are inputted.
Photo
SUM
307.2MB/973.7MB
Free
y
Caution
The glass screen of your PDP TV can break if the TV is accidentally dropped and hits the ground. Care should be taken.
Ensure two or more persons help when moving the product as a safety precaution. Do not lay the product lat on one side when moving.
Turn on your TV.
Photo
Music
Setup
2.
Connect a USB device
containing photo or music
iles to the
USB
jack on
the side of the TV.
L Move E Enter R Return
(Your) Samsung Plasma TV is a high quality television that has been carefully packaged to protect the integrity of its glass panel and component parts from damage
during transport. It is nonetheless a fragile piece of electronics that requires care in handling. Refrain from putting undue stress on any part of the packaging
unpacking, shipment, installation whether on a pedestal or mounted on the wall. Avoid placement of the TV that would expose its screen to any form of impact.
Breakage of the panel due to impact strike is not covered under the manufacturer’s warranty.
3.
When the Input selection screen is displayed, press the
r
button to select
Media Play (USB), then press the
ENTER
E button.
y
The exterior and screen of the product can get scratched during cleaning. Be sure to wipe the exterior and screen carefully using the cloth provided or a soft cloth to
prevent scratches.
[ Pobierz całość w formacie PDF ]